How to Clean the brake liningTools and materials:
1. Jack
2. Jac stand
3. Coarse Sandpaper
4. Key Ring 14 and 17
5. Lock Pas 14 and 17
6. Key Moment7. Lock Sock 18
8. Portable Impact Wrench
9. VaselineHow to Jack
1. Jack the car up to float and then given a jack stand, car jack both his right and left sides, jack stand 4 respectively given the right of the left front and right rear left.
2. Then prepare sock size 19 and portable impacy wrench, before using a portable tool wrench impacy push the button on the left to loosen pingir push, push right to tighten, then sock size 19 given or connected in portable impacy wrench, then portable impacy wrench connected with the air hose from the compressor and portable impacy wrench and sock size vehicle tires nut 19 affixed vertically, and then push to rotate the nut, the nut loosen vehicle tires are crossed. Then remove the tire. Release all the tires of vehicles.
3. How to release the brake, front brake (disc or disc):
First wasted wrench tool and lock ring 14 and 17.
Loosen the nut on the brake at the bottom
Then lift off the brake caliper and brake lining. After that refer to brake in check the condition of the brake is still low, medium, hight. If the normal brake then we sanding with sandpaper sandpaper is rough in the uneven surface of cotton brakes. If we have clean them with sandpaper and then we clean by using airgun (air compressor). And we spray (Brake Cleaner) evenly.
Then the brake is given vaseline on the end.
Then we put the brake lining.4. How to clean the rear brake (drum):
First, we have prepared a tool that is key T30 size sock star.
Then we loosen the locking bolt drum. Then remove the drum.
Then we sandpaper brake, we sandpaper surface section brakes are not flush with the way we sanding parallel. After sanded we spray with airgun (air compressor) after we spray cleaned using (Brake Cleaner). Then we replace the drum and we tighten the locking bolt.
5. Then we put all our wheels of the vehicle and tighten the locking wheel nut by using kincu sock size 19 as well as by using portable impacy wrench and we push the right part to tighten. Tightening the nut is crossed.
6. Once we feel we've all wrong car jack again to take the jack stand. We take all the jack stand and lower the car.
7. After the unloaded vehicle we prepare a key moment, our moment with size 10-12 Kg. Then tighten the lock nut until the sound of a vehicle wheel.
1. Jack
2. Jac stand
3. Coarse Sandpaper
4. Key Ring 14 and 17
5. Lock Pas 14 and 17
6. Key Moment7. Lock Sock 18
8. Portable Impact Wrench
9. VaselineHow to Jack
1. Jack the car up to float and then given a jack stand, car jack both his right and left sides, jack stand 4 respectively given the right of the left front and right rear left.
2. Then prepare sock size 19 and portable impacy wrench, before using a portable tool wrench impacy push the button on the left to loosen pingir push, push right to tighten, then sock size 19 given or connected in portable impacy wrench, then portable impacy wrench connected with the air hose from the compressor and portable impacy wrench and sock size vehicle tires nut 19 affixed vertically, and then push to rotate the nut, the nut loosen vehicle tires are crossed. Then remove the tire. Release all the tires of vehicles.
3. How to release the brake, front brake (disc or disc):
First wasted wrench tool and lock ring 14 and 17.
Loosen the nut on the brake at the bottom
Then the brake is given vaseline on the end.
Then we put the brake lining.4. How to clean the rear brake (drum):
First, we have prepared a tool that is key T30 size sock star.
Then we loosen the locking bolt drum. Then remove the drum.
Then we sandpaper brake, we sandpaper surface section brakes are not flush with the way we sanding parallel. After sanded we spray with airgun (air compressor) after we spray cleaned using (Brake Cleaner). Then we replace the drum and we tighten the locking bolt.
5. Then we put all our wheels of the vehicle and tighten the locking wheel nut by using kincu sock size 19 as well as by using portable impacy wrench and we push the right part to tighten. Tightening the nut is crossed.
6. Once we feel we've all wrong car jack again to take the jack stand. We take all the jack stand and lower the car.
7. After the unloaded vehicle we prepare a key moment, our moment with size 10-12 Kg. Then tighten the lock nut until the sound of a vehicle wheel.
 |
|
Komentar
Posting Komentar